Article | REF: IN701 V1

NH3/H2O absorption-based cold and electricity combined production cycle

Authors: Simone BRACCIO, Hai Trieu PHAN, Nicolas TAUVERON, Nolwenn LE PIERRÈS

Publication date: November 10, 2022

You do not have access to this resource.
Click here to request your free trial access!

Already subscribed? Log in!


Overview

Français

ABSTRACT

An absorption cycle integrated with a turbine allows the co-production of cold and electricity. This technology is very promising for its ability to harness low temperature heat sources more efficiently than separate production with simple thermodynamic cycles. The development of a detailed model of the complete cycle makes it possible to evaluate the performance achievable and the interest of this technology. Based on the numerical studies, a pilot plant was developed and tested on a laboratory scale to better understand the functioning of the cycle and the design challenges. The results will be very important for future development and scale-up of the technology for use in application to be identified.

Read this article from a comprehensive knowledge base, updated and supplemented with articles reviewed by scientific committees.

Read the article

AUTHORS

  • Simone BRACCIO: Research engineer - CEA Grenoble LITEN/DTCH, laboratory LOCIE UMR 5271 CNRS, University Savoie Mont-Blanc

  • Hai Trieu PHAN: Research engineer - CEA Grenoble LITEN/DTCH

  • Nicolas TAUVERON: Research engineer - CEA Grenoble LITEN/DTCH

  • Nolwenn LE PIERRÈS: University Professor - LOCIE Laboratory UMR 5271 CNRS, Savoie Mont-Blanc University

 INTRODUCTION

Given the ever-increasing global demand for energy, and the attention being paid to environmental issues and climate change, research is increasingly being carried out into new, more efficient cooling and electricity production technologies based on renewable or recovered sources. In this context, absorption systems are well suited to harnessing low-temperature energy for cold production. The advantage of these machines is that mechanical compression is replaced by thermochemical compression, using heat as the energy source. In addition to the control systems, the main electricity input is for a pump, but this is around 10 to 30 times less than that required for a compressor. Another advantage of absorption machine technology is that it can produce cold using well-known refrigerants such as ammonia or water, which are not harmful to the ozone layer and do not emit greenhouse gases. Absorption cooling systems have until now been niche technologies, but the market is growing with a reduction in their costs, which were halved between 2007 and 2016 according to a European study. Such systems are particularly promising in two areas: the recovery of industrial waste heat, and the use of renewable heat sources, especially in solar air-conditioning where the solar resource is well suited to the cooling requirement.

Although characterized by a low level of technological maturity (TRL 3-4 on a maturity scale of up to 9), the co-production, within the same cycle, of electricity and cooling from a low-temperature thermal source is the subject of numerous studies. Such a system would make it possible to increase the energy efficiency of the overall system and to mutualize certain components. This article focuses on a combined system for parallel production of cooling and electricity from a low-temperature heat source. The study is based on an experimental prototype of a water/ammonia absorption chiller with a thermal power of 10 kW at the generator, in which a turbine is integrated. A 1D model of the turbine, calibrated on CFD (Computational Fluid Dynamics) simulations, is integrated into a validated model of the absorption machine and used to study the interactions between the turbine and the cycle containing it. The constraints imposed by the turbomachine on the cycle are highlighted, and solutions for increasing the system's flexibility are proposed.

The analyses carried out have enabled us to define the cycle's operating range and study its performance. These results, together with feedback from the prototype, will be very important for the future development of a full-scale demonstrator for an application yet to be identified.

Note :

A table of acronyms, notations and symbols is provided at the end of the article....

You do not have access to this resource.

Exclusive to subscribers. 97% yet to be discovered!

You do not have access to this resource.
Click here to request your free trial access!

Already subscribed? Log in!


The Ultimate Scientific and Technical Reference

A Comprehensive Knowledge Base, with over 1,200 authors and 100 scientific advisors
+ More than 10,000 articles and 1,000 how-to sheets, over 800 new or updated articles every year
From design to prototyping, right through to industrialization, the reference for securing the development of your industrial projects

KEYWORDS

absorption   |   Combined cycle   |   Ammonia/water   |   Axial turbine


This article is included in

Industrial cooling

This offer includes:

Knowledge Base

Updated and enriched with articles validated by our scientific committees

Services

A set of exclusive tools to complement the resources

Practical Path

Operational and didactic, to guarantee the acquisition of transversal skills

Doc & Quiz

Interactive articles with quizzes, for constructive reading

Subscribe now!

Ongoing reading
NH3/H2O absorption cycle for co-generation of cooling and electricity