Article | REF: P1051 V1

Texture of divided materials Pore size of nanoporous materials from nitrogen adsorption

Authors: Françoise ROUQUEROL, Jean ROUQUEROL, Isabelle BEURROIES, Philip LLEWELLYN, Renaud DENOYEL

Publication date: June 10, 2017, Review date: October 23, 2020

You do not have access to this resource.
Click here to request your free trial access!

Already subscribed? Log in!


Overview

Français

ABSTRACT

This article describes the determination of the pore-size distribution of nanoporous materials by nitrogen adsorption. After presenting two basic theories (Kelvin and DFT) it presents (i) two methods suited to the study of pores smaller than 2 nm (micropores): Sing’s ?s and Horvath and Kawazoe’s method, (ii) the Barrett, Joyner and Halenda (BJH) method for pores between 2 and 50 nm (mesopores), and (iii) the application of DFT to the study of both micropores and mesopores. The merits and limits of each method are stated.

Read this article from a comprehensive knowledge base, updated and supplemented with articles reviewed by scientific committees.

Read the article

AUTHORS

  • Françoise ROUQUEROL: Professor emeritus at Aix-Marseille Université Aix-Marseille Université-CNRS, Laboratoire MADIREL unité mixte de recherche n° 7246, France

  • Jean ROUQUEROL: Emeritus Research Director at CNRS Aix-Marseille Université-CNRS, Laboratoire MADIREL Unité mixte de recherche No. 7246, France

  • Isabelle BEURROIES: Senior Lecturer at Aix-Marseille Université Aix-Marseille Université-CNRS, Laboratoire MADIREL unité mixte de recherche n° 7246, France

  • Philip LLEWELLYN: Director of Research at CNRS Aix-Marseille University-CNRS, MADIREL Laboratory, Joint Research Unit No. 7246, France

  • Renaud DENOYEL: Director of Research at CNRS Aix-Marseille University-CNRS, MADIREL Laboratory, Joint Research Unit No. 7246, France

 INTRODUCTION

This article reviews the most widely used methods for characterizing the pore size of nanoporous materials by nitrogen adsorption, in the width range from 0.1 to 50 nm.

Even when they are of natural origin (activated carbons, activated clays), these materials are most often treated to "adjust" them (in terms of pore size, specific surface area, surface chemical functions, etc.) with a view to their applications, which are numerous and include the following:

  • lowering natural gas storage pressure (to lighten cylinders and enable their use on natural gas-powered vehicles);

  • purification and recycling of aircraft atmosphere;

  • retention and reuse of petrol vapours from car fuel tanks;

  • retention and reuse of solvent vapours from paint tunnels;

  • remediation of soils contaminated by heavy metals;

  • separation of gases from air at ambient temperature, without the need for energy-intensive liquefaction and distillation;

  • the storage and gradual release (or "sustained release") of active drug ingredients, to ensure constant concentration in the body despite widely spaced drug doses;

  • the development of solar refrigeration machines exploiting the highly endothermic nature of water or alcohol vapour desorption for vaccine storage in desert environments;

  • recovery of hydrogen from refinery off-gases (where it costs nothing) for use as a clean fuel;

  • carbon dioxide sequestration to limit global warming.

It's easy to see why pore width plays such an important role in these applications. It is this width that enables us to develop both "molecular sieve" properties, allowing only a certain size of molecule to pass through, and physical adsorption energy (the narrower the pore, the higher the energy), enabling us to exploit the corresponding thermal effect, or a permeability to gases and liquids (thanks to several "hierarchical" pore sizes) capable of accelerating chemical engineering operations, or even the "useful" storage capacity of gases with sufficient adsorption energy to allow good retention but low enough to allow easy and as complete as possible recovery of the gas...

To characterize the size of nanopores, this article uses nitrogen adsorption, which is the most widely used approach, especially when the material itself is intended for an application involving adsorption.

Today's automated equipment makes it possible to carry out routine measurements, which is a definite advantage,...

You do not have access to this resource.

Exclusive to subscribers. 97% yet to be discovered!

You do not have access to this resource.
Click here to request your free trial access!

Already subscribed? Log in!


The Ultimate Scientific and Technical Reference

A Comprehensive Knowledge Base, with over 1,200 authors and 100 scientific advisors
+ More than 10,000 articles and 1,000 how-to sheets, over 800 new or updated articles every year
From design to prototyping, right through to industrialization, the reference for securing the development of your industrial projects

This article is included in

Analysis and Characterization

This offer includes:

Knowledge Base

Updated and enriched with articles validated by our scientific committees

Services

A set of exclusive tools to complement the resources

Practical Path

Operational and didactic, to guarantee the acquisition of transversal skills

Doc & Quiz

Interactive articles with quizzes, for constructive reading

Subscribe now!

Ongoing reading
Texture of divided materials