Article | REF: E3977 V1

Electrical interfaces for piezoelectric mechanical energy harvesting devices

Authors: Mickaël LALLART, Elie LEFEUVRE

Publication date: April 10, 2021, Review date: September 27, 2021

You do not have access to this resource.
Click here to request your free trial access!

Already subscribed? Log in!


Overview

Français

ABSTRACT

Harvesting efficiently energy from mechanical vibrations requires the use of suitable electrical interfaces behind piezoelectric transducers along with specific control laws. This article devises the effect of elementary or advanced energy extraction circuits on the harvested power or bandwidth. Several kinds of such electrical interfaces and associated control laws are detailed, allowin, the maximization of the generated electrical power or even the adaptation of its resonance frequency according to the electromechanical characteristics of the transducer in order to exploit ambient vibrations in an optimal way.

Read this article from a comprehensive knowledge base, updated and supplemented with articles reviewed by scientific committees.

Read the article

AUTHORS

  • Mickaël LALLART: University Professor - Electrical Engineering and Ferroelectricity Laboratory, - Lyon National Institute of Applied Sciences, - Villeurbanne, France

  • Elie LEFEUVRE: University Professor - Center for Nanoscience and Nanotechnology, Université Paris-Saclay and CNRS, Palaiseau, France

 INTRODUCTION

The recovery of small-scale ambient mechanical energy (power of the order of a few tens of microwatts to a few milliwatts) is of growing interest in a wide variety of application areas: industry, transport (goods, people, energy), the medical field, the general public, etc. This interest is linked to the development of a wide variety of autonomous electronic devices, most of which are powered by rechargeable batteries or cells. This interest is linked to the development of a wide variety of autonomous electronic devices, most of which are powered by rechargeable batteries. Mechanical energy is present in most environments, in different forms and with different characteristics. Capturing and converting this ambient mechanical energy into electricity can extend battery life, space out battery recharging, and in some cases even eliminate the need for energy storage.

Several technologies for converting mechanical energy into electricity can be considered for this type of application. The most conventional are based on the principles of magnetodynamic, piezoelectric and electrostatic transduction. This article focuses specifically on piezoelectric transduction, which offers numerous advantages for small-scale energy recovery from ambient mechanical vibrations: simple implementation, compactness, high energy density, high efficiency over a wide frequency range. However, the development of compact, efficient energy recovery systems using piezoelectric transducers requires suitable interface circuits. From an electrical point of view, a piezoelectric transducer does not behave like an ideal voltage or current generator, but like a generator with an internal impedance whose modulus and phase vary quite widely. In addition, the amplitude of the electrical quantities generated by the piezoelectric effect depends on ambient vibrations, and can also vary widely. For all these reasons, optimal extraction of the electrical energy generated by piezoelectric transduction requires suitable interface circuits and specific control principles, which are outlined in this article.

Despite high conversion efficiency, the electromechanical coupling of a piezoelectric energy recovery device can be relatively weak, depending on the materials used and the mechanical structure implemented. In this case, specific interface circuits are proposed to significantly increase the level of electrical power recovered. From an energy point of view, the effect of these circuits can be likened either to an improvement in the electromechanical transduction properties of the piezoelectric device, or to better control of energy exchanges (including the reactive part). In the case of piezoelectric resonators with strong electromechanical coupling, some of these interface circuits optimize power while offering...

You do not have access to this resource.

Exclusive to subscribers. 97% yet to be discovered!

You do not have access to this resource.
Click here to request your free trial access!

Already subscribed? Log in!


The Ultimate Scientific and Technical Reference

A Comprehensive Knowledge Base, with over 1,200 authors and 100 scientific advisors
+ More than 10,000 articles and 1,000 how-to sheets, over 800 new or updated articles every year
From design to prototyping, right through to industrialization, the reference for securing the development of your industrial projects

KEYWORDS

piezoelectricity   |   energy harvesting   |   electrical interfaces   |   converters


This article is included in

Electronics

This offer includes:

Knowledge Base

Updated and enriched with articles validated by our scientific committees

Services

A set of exclusive tools to complement the resources

Practical Path

Operational and didactic, to guarantee the acquisition of transversal skills

Doc & Quiz

Interactive articles with quizzes, for constructive reading

Subscribe now!

Ongoing reading
Interface circuits for piezoelectric mechanical energy recovery devices